Impulse Sealer, Plastic Bag Sealer Next Page

Add to Cart

Impulse sealers can be used in the laboratory for securely sealing specimen bags and to insure a water and airtight seal for autoclaving and sterilization procedures. These heatsealers provide an exceptional 2 mm wide air and watertight seal on most plastic materials up to 6 mm in thickness, including polyethyelene, polypropylene, polyurethane and more. Seal length is 305 mm (12"). An adjustable timer knob allows you to set the timing of the heating element according to the type of plastic you are sealing. All sealers are pretested and provide a warranty that guarantees dependability and durability. The impulse sealers are highly energy-efficient; the heating element only heats up and uses power when sealing. Comes fully assembled. UL and CE listed. Add to Cart

These items are currently unavailable:

Notify Me When Available

Select out of stock items above and enter your email address. As soon as each of these items becomes available at SKS, you will receive an automatic notification sent to this email address.

Notify Me When Available

Product Info

Stock#	Hgt	Wd	Lgt
MACH300	178 mm	375 mm	83 mm

Features:

• Seal Length: 305 mm (12")
• Seal Thickness: 6 mm (.236")
• Seal Width: 2 mm (.079")
• Power Consumption: 380 watts
• Voltage: AC 120V, 60 Hz
• Weight: 11 lbs
• Plugs into standard 110 volt socket (USA) - no special wiring needed
• Manufacturer tested and comes with warranty
• Energy-efficient -- only uses power when sealing
• Heating element only hot when sealing
• Makes airtight/watertight seal on virtually any heatsealable material in seconds
• Works on most plastics up to 6 mm thick
• Comes fully assembled
• 8 timer settings allow adjustments based on thickness of material
• UL and CE approved

Instructions for Use:

• Plug cord (14) into AC outlet. Machine will operate only when arm (2) is depressed. Regulate the timer (17) according to thickness of material to be sealed. Use a higher number for thicker material (settings 1- 8). Pull handle (1) down. Sealing takes place when light is on. Leave down for an additional second after light goes off for a better seal
• Set timer (17) to a lower number if seal burns through
• Raise timer to a higher number if material isn't fully sealed
• If bag sticks to silicon rubber (5), give more cooling time
• Once you set the timer (17), machine will remain constant
• Machine will not operate unit until handle (1) is lowered
• Close supervision is required when the product is used near children

Notes:

• Always keep sealing platform clean. Leaving residue will reduce life of element, Teflon (11, 12) and silicon rubber (5).
• Never use moisture to clean sealing surface
• Replace torn Teflon (11, 12) at once. A torn cloth will damage the element. Every time you replace the element, replace the lower (11) and upper (12) Teflon cloth
• For best operation, use only genuine replacement parts
• Change the silicon (5) when worn or burned
• Unplug wire (14) when servicing the machine
• To protect against risk of electric shock, connect to properly grounded outlet only

Compatible Plastic Types:

• Polyethylene (PE)
• Polyurethane (PU)
• Polypropylene (PP)
• Pliofilm
• Kel-F
• Polyflex
• Mylar
• PVA
• Tivac
• Saran
• Nylon
• Other heatsealable materials

Heating Adjustment List:

Timer Setting	Polyethylene (PE)	Polypropylene (PP) or High-Heat Film
1	UNDER .06 mm	-
2	UNDER .1 mm	-
3	UNDER .14 mm	-
4	UNDER .2 mm	UNDER .03 mm
5	-	UNDER .044 mm
6	-	UNDER .06 mm
7	-	UNDER .08 mm

Description of Parts:

• 1. Handle Knob
• 2. Platen Arm
• 3. Platen Spring
• 4. Platen
• 5. Silicon Rubber
• 6. Swivel
• 7. Hinge
• 8. Hinge Bracket
• 9. Enclosure
• 10. Metal Plate

• 11. Lower Element Teflon
• 12. Upper Teflon Cloth
• 13. Strain Relief Brushing
• 14. Power Supply Cord
• 15. Heating Element
• 16. Pilot Lamp
• 17. Timer Knob
• 18. Control Panel
• 19. Variable Resistor
• 20. Switch Level

• 21. Wire Connector
• 22. Internal Wiring
• 23. Heater Transformer
• 24. Connectors
• 25. Microswitch
• 26. Switch Bracket
• 27. Switch Insulation
• 28. Switch Lever Spring

• 29. Switch Lever (Bottom View)
• 30. Heater Terminal Assembly
• 31. Grounding Wire
• 32. Cover Plate
• 33. Printed Wiring Board
• 34. Relay
• 35. Rubber Foot & Screw

Connection Diagram:

Other Options

Clear PE Plastic Sample Bags, Large

Ecoheat Heat Gun Kit

Frequently Purchased With...

Clear PE Plastic Sample Bags, Small	Wash Bottles, Narrow Mouth Wash Bottles	Dosys™ 155 All Glass Syringes
Clear PE Loctop Sample Bags w/ Writing Area	Clear PE Plastic Sample Bags, Small	Dosys™ 155 All Glass Syringes
Wash Bottles, Narrow Mouth Wash Bottles	Clear PE Loctop Sample Bags w/ Writing Area

---

• 

Impulse sealers can be used in the laboratory for securely sealing specimen bags and to insure a water and airtight seal for autoclaving and sterilization procedures. These heatsealers provide an exceptional 2 mm wide air and watertight seal on most plastic materials up to 6 mm in thickness, including polyethyelene, polypropylene, polyurethane and more. Seal length is 305 mm (12"). An adjustable timer knob allows you to set the timing of the heating element according to the type of plastic you are sealing. All sealers are pretested and provide a warranty that guarantees dependability and durability. The impulse sealers are highly energy-efficient; the heating element only heats up and uses power when sealing. Comes fully assembled. UL and CE listed.